Haas Settings: 1 – Auto Power Off Timer

Haas Settings: 2- Power Off at M30

Haas Settings: 4 – Graphics Rapid Path

Haas Settings: 5 – Graphics Drill Point

Haas Settings: 6 – Front Pannel Lock

Haas Settings: 7 – Parameter Lock

Haas Settings: 8 – Prog Memory Lock

Haas Settings: 9 – Dimensioning

Haas Settings: 10 – Limit Rapid at 50%

Haas Settings: 11 – Baud Rate Select

Haas Settings: 12 – Parity Select

Haas Settings: 13 – Stop Bit

Haas Settings: 14 – Synchronization

Haas Settings: 15 – H & T Code Agreement

Haas Settings: 16 – Dry Run Lock Out

Haas Settings: 17 – Opt Stop Lock Out

Haas Settings: 18 – Block Delete Lock Out

Haas Settings: 19 – Feedrate Override Lock

Haas Settings: 20 – Spindle Override Lock

Haas Settings: 21- Rapid Override Lock

Haas Settings: 22 – Can Cycle Delta Z

Haas Settings: 23 – 9xxx Progs Edit Lock

Haas Settings: 24 – Leader To Punch

Haas Settings: 25 – EOB Pattern

Haas Settings: 26 – Serial Number

Haas Settings: 28 – Can Cycle Act w/o X/Z

Haas Settings: 29 – G91 Non-Modal

Haas Settings: 30 – 4th Axis Enable

Haas Settings: 31 – Reset Program Pointer

Haas Settings: 32 – Coolant Override

Haas Settings: 33 – Coordinate System

Haas Settings: 34 – 4th Axis Diameter

Haas Settings: 35 – G60 Offset

Haas Settings: 36 – Program Restart

Haas Settings: 37 – RS-232 Data Bits

Haas Settings: 38 – Aux Axis Number

Haas Settings: 39 – Beep @ M00, M01, M02, M30

Haas Settings: 40 – Tool Offset Measure

Haas Settings: 41 – Add Spaces RS-232 Out

Haas Settings: 42 – M00 After Tool Change

Haas Settings: 43 – Cutter Comp Type

Haas Settings: 44 – Min F in Radius TNC %

Haas Settings: 45 – Mirror Image X-axis

Haas Settings: 46 – Mirror Image Y-axis

Haas Settings: 47 – Mirror Image Z-axis

Haas Settings: 48 – Mirror Image A-axis

Haas Settings: 49 – Skip Same Tool Change

Haas Settings: 50 – Aux Axis Sync

Haas Settings: 51 – Door Hold Override (Safety Switch Override)

Haas Settings: 52 – G83 Retract Above R

Haas Settings: 53 – Jog w/o Zero Return

Haas Settings: 54 – Aux Axis Baud Rate

Haas Settings: 55 – Enable DNC from MDI

Haas Settings: 56 – M30 Restore Default G

Haas Settings: 57 – Exact Stop Canned X-Z

Haas Settings: 58 – Cutter Compensation

Haas Settings: 59 – Probe Offset X+

Haas Settings: 60 – Probe Offset X-

Haas Settings: 61 – Probe Offset Z+

Haas Settings: 62 – Probe Offset Z-

Haas Settings: 63 – Tool Probe Width

Haas Settings: 64 – T. OFS Meas Uses Work

Haas Settings: 65 – Graph Scale (Height)

Haas Settings: 66 – Graphics X Offset

Haas Settings: 67 – Graphics Y Offset

Haas Settings: 69 – DPRNT Leading Spaces

Haas Settings: 70 – DPRNT Open/CLOS DCode

Haas Settings: 71 – Default G51 Scaling

Haas Settings: 72 – Default G68 Rotation

Haas Settings: 73 – G68 Incremental Angle

Haas Settings: 74 – 9xxx Progs Trace

Haas Settings: 75 – 9xxxx Progs Singls BLK

Haas Settings: 76 – Tool Release Lock Out

Haas Settings: 77 – Scale Integer F

Haas Settings: 78 – 5th axis Enable